Contact
Tel: 18037961302
Sales hot line ( 24 hours  service): 18037961302

E-Mail: firstfurnace@gmail.com

whatsapp:+8618037961302

Adress: Luoxin Industrial Park, Luoyang, Henan
  • Products
  • Gear hardening machine

    Large diameter steel pipe quen

    Piston rod quenching and tempe

    Hand-held induction heater

    Grinding rod quenching and tem

    Induction forging machine

    induction heating machine 

    Induction heater

    High frequency induction heate

    Super audio induction heating

    Super audio induction heating

    Guideway quenching integrated

    Quenching equipment for machin

    Round steel end heating furnac

    Steel pipe heat treatment prod

    Square steel quenching and tem

    Sucker rod quenching and tempe

    Thickened petroleum steel pipe

    Round steel quenching and temp

    Steel pipe quenching and tempe

    Steel plate quenching and temp

    Induction Hardening Machine&nb

    Flywheel ring gear high freque

    Oil drill pipe quenching and t

    Iron induction furnace

    Aluminum melting furnace

    Copper melting furnace

    Small steel melting furnace

    Electric furnace technical parameters(歌方
        

    1. The fast furnace saves electricity compared to the slow furnace. The same set of equipment is faster than slow power saving. The timing and tightness of feeding and the size of the furnace will affect the melting speed. At this point, the best power consumption must be achieved at the same time.

    2, the need to take into account the current meter, try to make the power stable. Maximize the output power of the device as much as possible.

    3. Precisely control the temperature of molten iron. Do not let the temperature be too high or too high. It is not good for electricity consumption and lining life. A good furnace can save electricity and be efficient.

    4. Choose the right equipment. If the furnace is too large or too small, it may increase the power consumption. The same large furnace saves power, and the same fast induction melting furnace saves electricity. The high voltage is lower than the low voltage. Casting time also affects power consumption, preferably 5-10 minutes.

    5, do not need low-end equipment (also not high price is good, after the agent sales price is high, there is no long-term protection). The market is fiercely competitive. Some manufacturers cut corners and compete at low prices, and the worse the equipment consumption is, the greater the loss. If the copper row is not plated directly and used with a thinner copper material, the device will start to look the same, but the power consumption will be higher and higher.

    6, the line can not be saved, must be large enough, otherwise the long-term loss is quite amazing.

    7, develop a good boot habit, power as much as possible and reduce the insulation or baking time. When the power is not full, the power factor is low and the loss is large.

    8, improve the utilization of the transformer is also equal to saving electricity. A 630KVA transformer should be able to turn 13-15T tons of molten iron within 10 hours. If you can only produce 10-11 tons, your average electricity price must be higher than him.

    9, scientific oven. When the medium frequency electric furnace is to be blown, the cooling water of the induction coil should be turned off (a third of the normal water volume). It is best to intermittently supply water to keep the water temperature above 55 degrees, so as to facilitate the smooth discharge of water vapor, which can shorten the drying. Furnace time. Some furnace workers did not pay attention to this point, and the water supply was normal. As a result, the water vapor discharged from the cold copper tube condensed into water, so that the oven was long and power-consuming, and the effect was not good.

    Reference power consumption:

    Fused iron: fast 520-610 degrees / ton, slow 750-980 degrees / ton

    Fused steel: fast 550-650 degrees / ton, slow 800-1000 degrees / ton

    Copper melting: 310-360 degrees / ton, molten aluminum: 200-260 degrees / ton


    Copyright© 2007-2013 songdao Electric furnace manufacturing Co,.Ltd All Rights Reserved
    Tel:18037961302 Sales hot line ( 24 hours service): 18037961302
    E-Mail:firstfurnace@gmail.com
    Adress: Luoxin Industrial Park, Luoyang, Henan