Contact
Tel: 18037961302
Sales hot line ( 24 hours service): 18037961302
Sales hot line ( 24 hours service): 18037961302
E-Mail: firstfurnace@gmail.com
whatsapp:+8618037961302
Adress: Luoxin Industrial Park, Luoyang, HenanLarge diameter steel pipe quen
Piston rod quenching and tempe
Grinding rod quenching and tem
High frequency induction heate
Quenching equipment for machin
Round steel end heating furnac
Steel pipe heat treatment prod
Square steel quenching and tem
Sucker rod quenching and tempe
Thickened petroleum steel pipe
Round steel quenching and temp
Steel pipe quenching and tempe
Steel plate quenching and temp
Induction Hardening Machine&nb
Flywheel ring gear high freque
Electric furnace technical parameters(参数）
induction melting furnaces often burn thyristors should focus on which parts?
2. The large current is out of control, the back pressure angle of the intermediate frequency voltage is too small, the trigger circuit has poor contact, and the continuity of the off time is also paid attention to.
Now that the quality of the components has passed, the reliability is already very high if the process is good. Inverter thyristors are relatively weak components. If it is damaged frequently, there must be a reason. Should focus on checking:
1) The RC absorption circuit of the inverter tube of the intermediate frequency furnace, focusing on checking whether the absorbing capacitor is open. At this time, a digital multimeter capable of measuring the capacitance should be used to detect the capacitor, and it is not enough to measure only its on and off. If the inverter absorption loop is broken, and the inverter tube is easily damaged;
2) Check whether the electrical parameters of the pipe meet the requirements, and eliminate the use of components flowing into the unqualified manufacturer;
3) Whether the water jacket of the inverter tube and other cooling water channels are blocked, although this situation is rare, it does appear and is easy to ignore.
4) Pay attention to the phenomenon that the load is sparked to the ground. This situation will form a sudden high voltage, causing damage to the inverter tube breakdown.
5) If the running angle is too large or too small, it will cause frequent overcurrent of the inverter tube, which will damage the pipe and cause permanent damage.
6) Without affecting the start-up, properly increase the intermediate frequency loop wiring inductance of the intermediate frequency power supply to the furnace body, which can alleviate the damage caused by the excessive di/dt of the inverter tube.
The reason why the induction melting furnace burns the thyristor is mainly caused by the large current and large voltage runaway.
2. The large current is out of control, the back pressure angle of the intermediate frequency voltage is too small, the trigger circuit has poor contact, and the continuity of the off time is also paid attention to.
Now that the quality of the components has passed, the reliability is already very high if the process is good. Inverter thyristors are relatively weak components. If it is damaged frequently, there must be a reason. Should focus on checking:
1) The RC absorption circuit of the inverter tube of the intermediate frequency furnace, focusing on checking whether the absorbing capacitor is open. At this time, a digital multimeter capable of measuring the capacitance should be used to detect the capacitor, and it is not enough to measure only its on and off. If the inverter absorption loop is broken, and the inverter tube is easily damaged;
2) Check whether the electrical parameters of the pipe meet the requirements, and eliminate the use of components flowing into the unqualified manufacturer;
3) Whether the water jacket of the inverter tube and other cooling water channels are blocked, although this situation is rare, it does appear and is easy to ignore.
4) Pay attention to the phenomenon that the load is sparked to the ground. This situation will form a sudden high voltage, causing damage to the inverter tube breakdown.
5) If the running angle is too large or too small, it will cause frequent overcurrent of the inverter tube, which will damage the pipe and cause permanent damage.
6) Without affecting the start-up, properly increase the intermediate frequency loop wiring inductance of the intermediate frequency power supply to the furnace body, which can alleviate the damage caused by the excessive di/dt of the inverter tube.
Iron induction furnace
Aluminum melting furnace
Copper melting furnace
Small steel melting furnace
Small induction melting furnace
Induction iron furnace
3T intermediate frequency iron melting f
0.25T Intermediate Frequency Furnace
0.5T Intermediate Frequency Furnace
Medium Frequency Furnace
2T Induction Melting Furnace
1T Induction Melting Furnace
500kg Induction Melting Furnace
250kg Induction Melting Furnace
Induction Melting Furnace
3 T Induction Melting Furnace
5T Induction Melting Furnace
1T One Belt Two Intermediate Frequency F
5T One Belt Two Intermediate Frequency F
3T One Belt Two Intermediate Frequency F
2T One Belt Two Intermediate Frequency F
5T Parallel Intermediate Frequency Furna
5T Intermediate Frequency Furnace
5T Series Intermediate Frequency Furnace
3T Series Intermediate Frequency Furnace
2T Series Intermediate Frequency Furnace
1T Series Intermediate Frequency Furnace
0.5T Series Intermediate Frequency Furna
0.25T Series Intermediate Frequency Furn
1T Parallel Intermediate Frequency Furna
2T Parallel Intermediate Frequency Furna
0.5T Parallel Intermediate Frequency Fur
Product Class